Search found 463 matches

by URALNUT60
Fri Mar 13, 2020 4:06 am
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Ural 650 crank small end bushing failure
Replies: 8
Views: 361

Re: Ural 650 crank small end bushing failure

My bad Snakeoil meant to say big end bearing is tight on journal no side play when I removed piston small end bushing came out in pieces, was just wondering if before I install new crank if I should replace small end bushing with better quality product, didn't know if there was known problem with th...
by URALNUT60
Thu Mar 12, 2020 7:58 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Ural 650 crank small end bushing failure
Replies: 8
Views: 361

Ural 650 crank small end bushing failure

Removed left side piston on 650 Ural crank left side rod big end bearing toast, when I pushed wrist pin out and removed piston small bushing came out in pieces, wrist pin didn't have any discoloration, some darkness on bushing pieces, anybody ever had problems with bushing?
by URALNUT60
Sun Feb 02, 2020 10:00 am
Forum: Ural/Dnepr 101 - Newbie Questions
Topic: 1WD vs 2WD Dnepr
Replies: 12
Views: 450

Re: 1WD vs 2WD Dnepr

I would direct this towards the 2wd owners and what for fix has been used to alleviate this problem, what part of the country do you live in? I have full time 2wd 650 Ural, no issues on driveline, just the motor, I have a buddy that is completely happy with his 1we 750 Ural, he takes it in some off ...
by URALNUT60
Fri Jan 31, 2020 4:50 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Best Tune for Hot Running?
Replies: 19
Views: 677

Re: Best Tune for Hot Running?

1st I have heard of modified cam for 650 from Crawford's Cycle, so how does it change torque curve? Is this a cam designed by Terry or someone else? Is there a thread on here about the product? Cost of cam? Thank you
by URALNUT60
Thu Jan 16, 2020 7:32 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Re: Oil feed diagram

Am I correct in saying that the only oil lubrication the connecting rod bearings get is from oil splashed on the crank? There is no other means of oil delivery to the rod bearings? Thanks
by URALNUT60
Thu Jan 16, 2020 5:21 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Re: Oil feed diagram

So the cap came off in the neighborhood, can't say I seen the drive gear for pump poking out the top, block away from house and returned, retightened cap, gear could of popped up I guess and seated itself at sometime, bike ran for close to 100 miles, anything can happen, could the bike make it that ...
by URALNUT60
Thu Jan 16, 2020 4:32 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Re: Oil feed diagram

Yes I watched his video and put it to use to prime and check oil pump and that passages are clear
by URALNUT60
Thu Jan 16, 2020 2:27 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Re: Oil feed diagram

Reason for all the questions, 97 650 original crank went around 5k miles, Right side con rod bearing froze up, rebuilt motor flushing all passages with cleaner and compressed air New big end bearings new crank, new oil pump, primed motor before putting covers on, everything seemed fine, cap on top o...
by URALNUT60
Tue Jan 14, 2020 9:16 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Re: Oil feed diagram

So when oil leaves the pump does it flow to front main bearing and cam bearing misting the camshaft and bushing and trickling down the pushrod tube oiling the top end and returning to sump through drain hole in head and cylinder, the rear main bearing is last to receive oil with excess hitting the s...
by URALNUT60
Tue Jan 14, 2020 2:33 pm
Forum: The Black Market
Topic: Dallas Craigslist Find 2006 Tourist- $4200
Replies: 4
Views: 323

Re: Dallas Craigslist Find 2006 Tourist- $4200

1 we shouldn't scare you as much as the 800 kms which equates with you feel the pain of working the bugs out with no factory warranty to soften the blow, I believe will have Denso alt and Herzog gears, still has the crummy Russian ignition, I would feel better below 4k
by URALNUT60
Tue Jan 14, 2020 8:20 am
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Re: Oil feed diagram

Thank you
by URALNUT60
Tue Jan 14, 2020 8:20 am
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Re: Oil feed diagram

Thank you
by URALNUT60
Mon Jan 13, 2020 8:10 pm
Forum: General Hammerin' and Wrenchin' (all model years)
Topic: Oil feed diagram
Replies: 17
Views: 737

Oil feed diagram

Has anybody ever seen a illustration of how oil flows through a ural 650 motor? Thanks
by URALNUT60
Thu Jan 09, 2020 8:26 pm
Forum: Ural/Dnepr 101 - Newbie Questions
Topic: Intro: New Ural Owner in PA
Replies: 21
Views: 827

Re: Intro: New Ural Owner in PA

York county, 1997 Ural sportsman, spent my youth at Raymond B Winters State park, 192 lot of good riding, Penn's Cave right up the road! Welcome
by URALNUT60
Sat Jan 04, 2020 11:04 am
Forum: The Black Market
Topic: Houston Craigslist - CJ750 with seized engine - $1,200
Replies: 9
Views: 764

Re: Houston Craigslist - CJ750 with seized engine - $1,200

Great project, prob won't last long!